by Tim & Jack Stocker
Objective: To build an automated panoramic tripod head for use in photography, the main purpose to accurately produce an image using many/hundreds of separate photographs, enabling very high detail and the ability to zoom in on minute details.
Components: After some research we decided to build our GigaPi using the following:-
Main camera support/gimbal: MDF frame, providing controlled tilt around the camera nodal ( no parallax) point. Lego Turntables to provide the pivot points and gearing.
Tripod Head/Pan control: Cheap laser level kit (Tribrach), Modified with a worm and gear drive.
Camera/Mount: MDF frame designed around a Canon 5DMKII, and a adapter plate top allow Lumix FZ100 to also be fitted. 'Fotomate' Focus Rail fitted to allow the no parallax point to be set for each camera and lens combination, connected to the frame using a bolt.
Drive: Two 5volt DC Stepper Motors, one for panning and the other for tilting, with worm drive gears fitted.
Control: Raspberry Pi to provide the computer control, including pan, tilt, shutter operation etc. Stepper motor driver circuit board attached directly to the Pi and shutter control circuit designed and built by us to operate the shutter electrically. Modified remote release cables for both cameras to enable easy connection to the board via a 3.5mm jack plug. USB hub connected to the Pi, to enable connection of a keyboard, memory stick etc. A rechargeable battery pack to be used to power the PI.
User interface: A 12 volt 5 inch display screen (actually a car reversing camera display) and a touch pad to provide the interface. All housed in a project/instrument box, with outlets for shutter, stepper motors, USB and charging point.
Software: Bespoke programme written by Jack to control every aspect of the operation of the GigaPi. The programme is required to calculate the horizontal and vertical angles required, the camera sensor size, the length of zoom used and the image overlap required, it then needs to calculate the total photos required to complete the task, operating the stepper motors the required amount in the right order and fire the shutter at the right time, allowing for focus and shutter activation time etc, a tall order indeed.
One inch thick MDF cut with a jigsaw and filed and sanded to a smooth finish, two lego turntables fitted to allow it to tilt, the pan/pivot point is set to the center of the camera lens.
A cheap 5volt DC stepper motor was fitted with a worm drive to turn the 56 tooth lego gear, an MDF block made to provide the correct spacing for the gears.
A cheap laser level kit brought off the internet provides the panning control, even comes with a tripod for around £20. the three plastic screw adjusters were removed as they had too much side play in them, replaced them nuts and bolts. A 40 tooth drive gear fitted on the center bolt which had to be modified to provide a 4mm shaft for the gear to fit onto. Another 5v stepper motor fitted to a hand made bracket and a worm drive gear press fitted to the shaft. Both motor wires were then fitted with an RJ45 jack plug to enable quick connection to the control box later on.
The completed framework was painted yellow to match the laser head, and a focus rail bolted into place to allow the nodal point of the camera lens to be set.
Raspberry Pi computer, you can also see attached the Stepper motor driver circuit, and two RJ45 sockets to allow easy connection to the two stepper motors, you can also see in the bottom right hand corner 4 wires soldered on to the back of the stepper motor board to provide the power, earth and activation of the focus and shutter control relays.
This is the shutter control circuit, designed by us and laid out on Vero board. it's is basically two 5v solid state relays which are activated and powered by the Pi. One controls the focus/exposure function, and the other controls the shutter. The relays close the circuit on the shutter release cables, starting with the focus/exposure function and this remains on whilst the shutter is activated a split second later.
This is the completed circuitry. The Raspberry Pi at the top, the stepper motor driver circuit fitted, the shutter activation on the right, the USB hub on the left and the touch pad and display screen.
The project/instrument box, was cut to allow fitment of all the components, plus the Anker Astro 3 rechargeable battery pack. A hole was made in the bottom of the box to allow access to the power button, and an on/off switch fitted to the front panel to allow the screen to be powered on and off.
The battery pack provides enough power for several hours work, provides both 5volt for the PI/stepper motors, and 12volts for the display screen.
This is the completed setup. It is fully portable and all the control cables can be unplugged easily.
The bespoke Raspberry Pi programme code: https://github.com/Frankincense/GigaPi
Stepper motor: http://www.ebay.co.uk/itm/290850433156?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
Stepper motor C code: http://unicorn.drogon.net/step.c
GPIO Stepper motor: http://www.raspberrypi.org/phpBB3/viewtopic.php?f=32&t=10483
Auto login scripts: http://www.raspberrypi.org/phpBB3/viewtopic.php?f=5&t=5225
GigaPi Panorama Calculator:http://photos.yves.over-blog.com/article-panorama-calculator-mise-a-jour-61831164.html
GigaPan Images: http://www.gigapan.com/gigapans?query=timstocker